[ITEM]
24.02.2019

C5 Window Height Adjustment C5

59

Window Adjustment 101 Door Window Height Adjustment (Major) Door Window Height Adjustment (Minor) Door Window Tip-In Adjustment Baseline Setting Remove door panel & water deflector. Remove door speaker assembly.

Remove window door clamp sight access plugs. Position window to access clamp nuts. Disconnect window switch. Loosen window clamp nuts through door top opening. Regulator in full UP position. Loosely tighten rear window clamp nut. With helper, position window to door opening.

Tighten window clamps to 89 lb/in. Open door and install window clamp access plugs.

Install speaker, water deflector, door panel. Perform minor height and tip-in adjustments as necessary: Window fully UP.

Remove large access plug (under front of door). Loosen window regulator front channel mounting nut.

13.1 Swiveling cuspidor (alternative equipment for C5+ only). In order to adjust the height of the dentist element, you. The LIVE IMAGE window opens.

Remove reflector from door panel. Loosen jack screw jam nut. Adjust tip-in with jack screw (clockwise = outward). Tighten jack screw jam nut. Lower window. Tighten window regulator front channel mounting nut. Raise window, check alignment.

Reinstall access plug & reflector. Door Window Height Adjustment (Minor) If window height is off less than 3mm. Open door and remove both small access plugs (under door). Loosen regulator jack screw jam nuts (both). Adjust both jack screws equally. Close the door and check alignment. Windows 7 32 bit sp1 download. Reinstall access plugs.

To install or remove the rear vent window on a 2001 Honda Civic you 1st have to take the rear door panel off. To remove the rear door panel you need to un-screw the screws hidden underneath the plastic door pull. The screws are not in the arm rest. Now you can pry the perimeter door panel fasteners off. Once the door panel is off, look for 2 (Gold colored) bolts. Follow the rear vent window channel downward with your eyes and you will see them.

They are about 1 foot apart from each other. Before you loosen the bolts put the window in the up position. When you un-screw the lower bolt a long odd shaped washer is going to drop into the bottom of the door.

Cut the plastic to get this washer. Your going to need it to re-install the vent channel. After you have the 2 bolts off follow the channel up this time all the way to the top of the door. Move the weatherstripping and you will see a small screw. Un-screw this screw and the channel will come out. Now you can install or remove the vent window.

[/ITEM]
[/MAIN]
24.02.2019

C5 Window Height Adjustment C5

2

Window Adjustment 101 Door Window Height Adjustment (Major) Door Window Height Adjustment (Minor) Door Window Tip-In Adjustment Baseline Setting Remove door panel & water deflector. Remove door speaker assembly.

Remove window door clamp sight access plugs. Position window to access clamp nuts. Disconnect window switch. Loosen window clamp nuts through door top opening. Regulator in full UP position. Loosely tighten rear window clamp nut. With helper, position window to door opening.

Tighten window clamps to 89 lb/in. Open door and install window clamp access plugs.

Install speaker, water deflector, door panel. Perform minor height and tip-in adjustments as necessary: Window fully UP.

Remove large access plug (under front of door). Loosen window regulator front channel mounting nut.

13.1 Swiveling cuspidor (alternative equipment for C5+ only). In order to adjust the height of the dentist element, you. The LIVE IMAGE window opens.

Remove reflector from door panel. Loosen jack screw jam nut. Adjust tip-in with jack screw (clockwise = outward). Tighten jack screw jam nut. Lower window. Tighten window regulator front channel mounting nut. Raise window, check alignment.

Reinstall access plug & reflector. Door Window Height Adjustment (Minor) If window height is off less than 3mm. Open door and remove both small access plugs (under door). Loosen regulator jack screw jam nuts (both). Adjust both jack screws equally. Close the door and check alignment. Windows 7 32 bit sp1 download. Reinstall access plugs.

To install or remove the rear vent window on a 2001 Honda Civic you 1st have to take the rear door panel off. To remove the rear door panel you need to un-screw the screws hidden underneath the plastic door pull. The screws are not in the arm rest. Now you can pry the perimeter door panel fasteners off. Once the door panel is off, look for 2 (Gold colored) bolts. Follow the rear vent window channel downward with your eyes and you will see them.

They are about 1 foot apart from each other. Before you loosen the bolts put the window in the up position. When you un-screw the lower bolt a long odd shaped washer is going to drop into the bottom of the door.

Cut the plastic to get this washer. Your going to need it to re-install the vent channel. After you have the 2 bolts off follow the channel up this time all the way to the top of the door. Move the weatherstripping and you will see a small screw. Un-screw this screw and the channel will come out. Now you can install or remove the vent window.